Your food blender is one of the essential electric appliances in your kitchen. When you have young children and older people with a weak digestive system, you must take time to blend their food. Besides, you can prepare juice to refresh yourself on hot days. However, after using it for some time, it might stall. That brings us to the question; why is the blender not turning on?
In most cases, a burned-out fuse is a major reason your blender won’t turn on. You can check if it’s the fuse that has blown out by opening the base cover of your blender. While there, check on the circuit board and the motor switch.
Table of Contents
Check The Blender Power Connectivity
It is necessary to check power connectivity if you realize your blender is not working well. You can check this by disconnecting the power cord and carrying a test of an electrical switch by turning your blender switch on. After that, pick the multimeter and press the switches of the blender one at a time. If you find there is low reading, do not worry since your switch is working.
Below are some multipurpose multimeters that will help you to check the power:
- Klein Tools 69149 Multimeter test kit
- AstroAI Digital Multimeter with Ohm Volt Amp
- KAIWEETS Digital Clamp Meter T-RMS 6000 Counts
Clean Blender Terminals
Another important thing you need to do to fix your blender that is not functioning well is by cleaning the terminals. To expose the screws holding the housing cover of the switch, you need to remove the plastic faceplate. Then remove the screws attaching the housing plate and follow the cleaning solvent’s steps to spray the openings and the terminals.
Using a quality-cleaning agent will help your blender to maintain its color. Consequently, when Reading the instruction manual from the manufacturer, you will gather more information about cleaning your blender terminals.
Check and Test the Fuse to Know Why Your Blender Is Not Turning On
The fuse is located at the wire end from the terminal, where the power cord is attached. Also, it would be vital if you chose the right voltmeter for easier reading. The high reading will always mean that the blender fuse requires some replacements. However, it is essential to consider buying one of the same sizes.
Check The Jams
Jamming is another thing that affects the functionality of the blender. For that case, you need to disassemble the drive and later turn the blade shaft. Thus, when the machine has a jam, you require to check what is causing such a problem.
In some cases, you will find that debris in the blender blades is causing the jamming. Moreover, you need to remove the debris or have the replacement of the coupling.
Check the Motor
The motor serves the user for a long time when the blender is used in the right way. It is possible to find that your motor is becoming unserviceable in some couple of years or months. When you find that your motor is not working, you can carry some tests using a multimeter.
Make sure the power source is unplugged before doing some testing. You can clip the meter probes to the plug prongs, press the speed switch and follow the meter reading.
If you want to purchase another motor to replace the older one, you can check out the different blenders in the market.
Also read: Why is My Keurig Making Noise?
Important Steps to Follow While Replacing Your Motor
When you find that your blender motor is faulty, you require to replace it. As an alternative, you need to change the motor instead of changing the whole unit. In doing so, you will save more resources and time.
The replacement of the motor is a job that will need professionalism. Nonetheless, with little knowledge, you can do the task on your own. When you have the right tools, follow the below steps to do a DIY motor replacement.
Step 1: The first thing is to unplug the motor from the power source. Then, unscrew the bottom cover with the right tools and remove the available inner cover.
Step 2: Open the screws and pull the motor carefully. However, before you handle this task, it is recommendable to take a photo to help you set up the new one.
Step 3: Here you need to disorder the wire using the soldering iron. Also, it is necessary to cut the wire. But this is dependent on the model type.
Step 4: This is an important step you cannot ignore. You require to place the new type at the point where you had installed the old one. Then solder the wires at their correct position.
Step 5: The final motor replacement process is putting the covers in the previous location, then plugging them into the power source and testing it.
Fix Your Blender Blades
Over time, the blender blades become blunt and weak. The cause of these problems is the debris left in the blades after the blending process. Therefore, ensure you clean your blender blades after every use. This challenge mainly affects the different types of blades since they play the major role of the blender.
Hopefully, this guide will help you get a solution to why is my blender not turning on. Additionally, it will enlighten you on the best way to fix your blender when it is not functioning well. Therefore, take your time to go through the guidelines to acquire more knowledge concerning the working of your blender.
If you don’t have the slightest idea of fixing the issue in your blender, you can look for an expert for professional help to solve your problem. Alternatively, you can consider buying a blender for senior citizens.